Rockford Fosgate - R250X1 - PRIME - Mono 1 X 250WRMS @ 2 OHMS
- mono subwoofer amplifier
- 150 watts RMS x 1 at 4 ohms (250 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- variable low-pass filter (50-250 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- phase switch
- wired remote Punch Level Control included
- Class AB amplifier design
- frequency response: 20-250 Hz
- MOSFET power supply
- preamp and speaker-level inputs
- preamp outputs
- 8-gauge power and ground leads and a 30-amp fuse recommended — wiring and hardware not included with amplifier
- no on-board fuses — when installing multiple amps in a system, an additional 30-amp in-line fuse between the distribution block and this amplifier is recommended
- 11-1/4"W x 2"H x 7-3/8"D
- warranty: 1 year
What's in the box?
- Mono subwoofer amplifier
- Remote Punch Level Control module
- 18' Remote Punch Level Control cable (RJ-25 connector on both ends)
- 6" Speaker level input harness
- 3mm Allen wrench
- Four 3/4" Self-tapping screws
- Two 1/2" Self-tapping screws
- 4 Flat washers
- Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
- Amplifier verification certificate
Features and Specs
|RMS Power Output (Watts x Channels)||150 x 1|
|Peak Power Output (Watts x Channels)||N/A|
|Power at 2 Ohms (Watts x Channels)||250 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||20-250 Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||80 dB|
|Low-Pass Crossover Frequency||50-250 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||45 Hz|
|Speaker Level Inputs||Harness|
|Preamp Outputs||1 pair|
CEA 2006 Compliant: The R250X1's power ratings and signal to noise ratio are measured according to the uniform standards advocated by the Consumer Electronics Association (CEA). This allows you to accurately compare these specifications for all CEA 2006-compliant amplifiers, even from different brands. Manufacturers who adhere to these standards can display the CEA 2006 logo on their products and packaging. CEA2006 Specifications for this amplifier are:
- 4 Ohms: 150 watts RMS x 1 at 4 ohms, 14.4 volts, and less than 1% THD+N
- 2 Ohms: 250 watts RMS x 1 at 2 ohms, 14.4 volts, and less than 1% THD+N
- S/N: 80 dB, measured at 1 watt output (100 dB measured at rated power)
LED Indicator: The amplifier is equipped with an LED power/protect indicator. The LED illuminates blue when the unit is turned on. It illuminates red if the thermal or short circuit protection circuit is engaged, and the amplifier will automatically turn off.
Mounting: The amplifier can be mounted vertically or horizontally using the supplied mounting screws. The amplifier should never be mounted in an engine compartment as this will void the warranty.
Gain Control: Use the amplifier's gain control to match the output of the source unit. The rotary gain control is labeled 1 to 11 and has a sensitivity range of 150mV to 4V when using a preamp level signal, 450mV to 12V when using a speaker level signal.
Remote Punch Level Control: The R250X1 includes a wired Remote Punch Level Control, linked to the gain control of the amplifier. The module allows you to remotely control the output level of the amplifier from the dash or center console. The Remote Punch Level Control features a rotary dial, and comes with mounting hardware and an 18' cable.
Note: The Remote Punch Level Control measures approximately 1-3/4" wide (2-5/8" including the mounting flange) x 3/4" high x 1-5/8" deep (2-1/8" deep including the knob and wiring).
Crossover: The amplifier is equipped with a 12dB/octave Butterworth low-pass crossover. The crossover point is continuously variable from 50 to 250 Hz. This being a subwoofer amp, the crossover is always engaged.
Phase: The 2-position phase switch allows you to easily reverse the output phase of the amplifier, choose 0° or 180° to match the rest of your vehicle's speaker system.
Punch EQ: The Punch EQ bass boost circuit is adjustable from 0 (min) to +12dB (max) and centered at 45Hz.
Power Terminals: The power and ground terminals are nickel-plated set screw terminals and will accommodate up to 4 gauge power and ground wires.
Fuse: An external 30-amp fuse (not included) must be installed on the power wire at the battery. If a wiring kit is used which includes a fuse with a value other than 30-amps, the original should be replaced with a 30-amp fuse.
Remote Turn-On Terminal: The remote turn-on terminal is a nickel-plated set screw terminal that will accommodate up to an 8 AWG wire. It's used to remotely turn the amplifier on and off.
Speaker Terminals: The one pair of speaker outputs is nickel-plated set screw terminals what will accommodate up to 8 AWG speaker wire.
RCA Input Jacks: The industry standard RCA jacks provide an easy connection for preamp level input. They are nickel-plated to resist signal degradation caused by corrosion.
Speaker Level Input: A speaker level input harness is included, making it easier to add the amplifier to a factory radio or to a receiver with no preamp outputs.
RCA Output Jacks: A pair of RCA pass-thru jacks provides a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of your vehicle to the amplifier location.
Wired Remote: An RJ-25 jack is used with the included Remote Punch Level Control.