Rockford Fosgate - PBR500X1 - Compact mono car amplifier — 500 watts RMS at 1
- mono subwoofer amplifier
- 175 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms)
- 500 watts RMS x 1 at 1 ohm
- CEA-2006 compliant
- Boosted Rail amp technology
- Dynamic Thermal Management cooling system
- variable low-pass filter (35-250 Hz, 12 dB/octave)
- differential-balanced inputs eliminate noise from your vehicle's electrical system
- preamp and speaker-level inputs
- optional wired remote bass boost(0-18 dB at 45 Hz)
- 8-gauge power and ground leads and an 80-amp fuse recommended — wiring and hardware not included with amplifier
- no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended
- 8-5/8"W x 1-9/16"H x 4-1/4"D
What's in the box?
- Mono amplifier
- 12" Input harness (Molex plug on one end and female stereo RCA jacks on the other)
- Installation & Operation manual (Eng/ Fren/ Span/ Ger/ Ita)
- Amplifier Performance Verification Certificate
Features and Specs
|RMS Power Output (Watts x Channels)||175 x 1|
|Peak Power Output (Watts x Channels)||500 x 1|
|Power at 2 Ohms (Watts x Channels)||300 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||1|
|Best Frequency Response||20-250 Hz|
|THD at Rated RMS Power||0.2%|
|Signal to Noise Ratio||85 dB|
|Low-Pass Crossover Frequency||35-250 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||Optional (0-18 dB)|
|Bass Boost Frequency||45 Hz|
|Speaker Level Inputs||Harness|
Boosted Rail Technology: The PBR500x1 uses Boosted Rail Technology (BRT), an efficient design that doesn't use a switching power supply. The PBR500x1's average efficiency is more than 75%, meaning it doesn't generate much heat and can maintain a small footprint.
Power Output: The power output increases as impedance is reduced:
- 4Ω: 175 watts RMS
- 2Ω: 300 watts RMS
- 1Ω: 500 watts RMS
Signal Input: The PBR500x1 is compatible with either line-level (RCA) or speaker-level inputs. The included Molex-to-RCA is used in both cases; the RCA end is cut off for connection to speaker wires.
Auto Turn-on: When using speaker-level inputs the amp will automatically turn on when it senses an input signal (4 volt minimum). The threshold voltage (DC offset) for auto turn-on is adjustable from 4 volts to 6 volts. This circuit is only active when the Input Level switch is set to High (speaker-level).
Dynamic Thermal Management (DTM): DTM Evenly distributes excess heat across the entire extruded aluminum heatsink.
MEHSA³: MEHSA³ (Maximum Efficiency Heat Sink Application-Third Generation) is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. The multi-layer insulated metal MEHSA substrate operates with minimal thermal resistance, spreading heat both downward and outward to quickly dissipate heat from each device across the heatsink. This allows greater power output, enhanced thermal stability, and maximum reliability.
NOMAD: NOMAD (NOn-Multiplying Advanced Decision) is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed.
DSM (Discrete Surface Mount): In the manufacturing process high speed robotics are used to place 1% tolerance parts and large board traces. DSM improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature.
LEDs: The Power/Protect LED on the right side of the amp illuminates blue when the amp is turned on and operating normally; it illuminates red when one of the protection circuits has engaged (short circuit, impedance too low, or temperature too high). The BRT LED on the left side of the amp illuminates white when the boost mode is engaged.
Crossover: The amplifier's internal low-pass crossover is continuously variable from 35 Hz to 250 Hz; the slope is 12 dB/octave.
Gain: When using line-level inputs, the input gain is adjustable from 150mV to 4V, when using speaker-level inputs it's adjustable from 400mV to 11V.
Input Level: Use the 2-position switch to select the input voltage range; High (speaker-level) or Low (line-level).
DC Offset: The DC offset threshold voltage for the auto turn-on circuit is adjustable from 4 volts to 6 volts (feature only active when the Input Level switch is set to High).
Power Connections: The power, ground, and remote turn-on terminals are c-clamps on a removable plug. Each terminal will accommodate up to 8-gauge wire (Rockford recommends 8-gauge minimum for the power and ground wires). A flat blade screwdriver (not supplied) is required to tighten/loosen the terminals. There is no fuse on the body of the amp, so an external 80-amp fuse (not included) must be installed in the power wire. If a wiring kit is used that includes a different value fuse, the original should be replaced with a 80-amp fuse.
Signal Input: The included input harness has a Molex plug on one end (plugs into the amp) and female RCA plugs on the other. When using speaker-level inputs the RCA end is removed and the four individual wires are used.
Speaker Output: The speaker outputs are c-clamps on a removable plug. Each terminal will accommodate up to 8-gauge wire
Remote Punch EQ (PEQ): An RJ-45 jack is provided for connecting an optional remote PEQ control (sold separately). When connected the PEQ acts as a variable bass boost; 0-18 dB centered at 45 Hz.
Note: Older model (prior to 2007) Punch Bass and Para-Punch remotes will not work with this amp.