Rockford Fosgate - PBR300X4 - Compact 4-channel car amplifier — 75 watts RMS x 4
- 4-channel car amplifier
- 75 watts RMS x 4 at 4 ohms
- non-bridgeable, 4-ohm stable per channel
- CEA-2006 compliant
- Boosted Rail amp technology
- Dynamic Thermal Management cooling system
- selectable high- and low-pass filters (80 Hz, 12 dB/octave)
- differential-balanced inputs eliminate noise from your vehicle's electrical system
- preamp and speaker-level inputs
- 10-gauge power and ground leads and a 30-amp fuse recommended — wiring and hardware not included with amplifier
- no onboard fuses — when installing multiple amps in a system, an additional 30-amp in-line fuse between the distribution block and the amplifier is recommended
- dimensions: 6-15/16"W x 1-9/16"H x 4-5/16"D
What's in the box?
- 4-Channel amplifier
- Two 7" Speaker output harnesses (Molex plug on one end and tinned bare wire on the other)
- Two 12" Input harness (Molex plug on one end and female stereo RCA jacks on the other)
- Installation & Operation manual (English/ French/ Spanish/ German/ Italian)
- Amplifier Performance Verification Certificate
Features and Specs
|RMS Power Output (Watts x Channels)||75 x 4|
|Peak Power Output (Watts x Channels)||N/A|
|Power at 2 Ohms (Watts x Channels)||N/A|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||4|
|Best Frequency Response||20-20K Hz|
|THD at Rated RMS Power||0.5%|
|Signal to Noise Ratio||80 dB|
|Low-Pass Crossover Frequency||80 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||80 Hz|
|High-Pass Slope (dB/octave)||12 dB/oct|
|Bass Boost Frequency||N/A|
|Speaker Level Inputs||RCA|
Boosted Rail Technology: The PBR300x4 uses Boosted Rail Technology (BRT), an efficient design that doesn't use a switching power supply. The PBR300x4's average efficiency is more than 75%, meaning it doesn't generate much heat and can maintain a small footprint.
Signal Input: The PBR300x4 is compatible with either line-level (RCA) or speaker-level inputs. The included Molex-to-RCA is used in both cases; the RCA end is cut off for connection to speaker wires.
Auto Turn-on: When using speaker-level inputs the amp will automatically turn on when it senses an input signal (4 volt minimum). The threshold voltage (DC offset) for auto turn-on is adjustable from 4 volts to 6 volts.
Dynamic Thermal Management (DTM): DTM Evenly distributes excess heat across the entire extruded aluminum heatsink.
MEHSA³: MEHSA³ (Maximum Efficiency Heat Sink Application-Third Generation) is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. The multi-layer insulated metal MEHSA substrate operates with minimal thermal resistance, spreading heat both downward and outward to quickly dissipate heat from each device across the heatsink. This allows greater power output, enhanced thermal stability, and maximum reliability.
NOMAD: NOMAD (NOn-Multiplying Advanced Decision) is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed.
DSM (Discrete Surface Mount): In the manufacturing process high speed robotics are used to place 1% tolerance parts and large board traces. DSM improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature.
LEDs: The Power/Protect LED on the right side of the amp illuminates blue when the amp is turned on and operating normally; it illuminates red when one of the protection circuits has engaged (short circuit, impedance too low, or temperature too high). The BRT LED on the left side of the amp illuminates white when the boost mode is engaged.
Crossover: The front and rear channels have independent crossover switches. Each can be set to low-pass, all-pass (crossover is bypassed), or high-pass. The crossover point is fixed at 80 Hz and the slope is 12 dB/octave.
Gain: The front and rear channels also have independent input gain controls, adjustable from 150mV to 11V.
2/4 Channel: When using only one set of inputs, set this switch to 2-channel and connect the inputs.
DC Offset: The DC offset threshold voltage for the auto turn-on circuit is adjustable from 4 volts to 6 volts (useful with speaker-level inputs).
Power Connections: The power, ground, and remote turn-on terminals are c-clamps on a removable plug. Each terminal will accommodate up to 10-gauge wire (Rockford recommends 10-gauge minimum for the power and ground wires). A flat blade screwdriver (not supplied) is required to tighten/loosen the terminals. There is no fuse on the body of the amp, so an external 30-amp fuse (not included) must be installed in the power wire. If a wiring kit is used that includes a different value fuse, the original should be replaced with a 30-amp fuse.
Signal Input: The included input harnesses have Molex plugs on one end (plugs into the amp) and female RCA plugs on the other. When using speaker-level inputs the RCA end is removed and the four individual wires are used.
Speaker Output: The included speaker output harnesses have Molex plugs on one end (plugs into the amp) and tinned bare wires on the other.