Kicker - 44KKP412 - 12 inch Kicker Sub and 4CH Amp Package

$529.00
Shipped in 2-3 Working Days
SKU
KKP412

Kicker - KKP412 - 12 inch Kicker Sub and 4CH Amp Package

Product Info

Kicker KKP412 4 Channel 12" C124 Kickpack Amplifiers and Loaded Enclosures Package

 

VC124 Enclosure Technical Specifications

Size(cm)

  • 30

Impedance (ohms)

  • 4

Power (watts/Channel) 2Ω Stereo

  • 60 x 2

Power (watts/Channel) 4Ω Stereo

  • 30 x 2

Power (watts/Channel) 4Ω Bridged

  • 125 x 1

DIM A (cm)

  • 28.5

DIM B (cm)

  • 37.1

DIM C (cm)

  • 40.9

DIM D (cm)

  • 44.8

DXA125.2 Amplifier Features and Specs

Performance
RMS Power Output (Watts x Channels) 30 x 4
Peak Power Output (Watts x Channels) ---
Power at 2 Ohms (Watts x Channels) 60 x 4
Bridged Power (Watts x Channels) 125 x 2
Minimum Impedance Bridged 4
Minimum Impedance Unbridged 2
Best Frequency Response 10-20000 Hz
THD at Rated RMS Power 1%
Signal to Noise Ratio 95 dB
Input Voltage 14.4v
Features
Amplifier Class AB
Low-Pass Crossover Frequency 50-200 Hz
Low-Pass Slope (dB/octave) 12 dB/octave
High-Pass Crossover Frequency 50-200 Hz
High-Pass Slope (dB/octave) 12 dB/octave
Bass Boost 0-12 dB
Bass Boost Frequency 40 Hz
Fan Cooled No
Fuse Rating 60
Speaker Level Inputs RCA
Preamp Outputs No
Width (inches) 12
Height (inches) 2-3/8
Depth (inches) 7-1/8
   

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over the full frequency range of the amp with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels at a reference of 1 watt. CEA-2006 allows consumers to compare car amplifiers and receivers on equal footing. Measured under CEA-2006 conditions the Kicker DXA250.4 is rated at 30 watts RMS x 4 channels into a 4-ohm load and the signal to noise ratio is >95 dB. Additional specs listed in the manual (but not listed as CEA-2006 compliant) include 60 watts RMS x 4 channel into a 2-ohm load (measured using a 14.4 volt power supply with no more than 1% THD+N) and 95 dB signal-to-noise ratio (measured at the rated power output).

Auto Turn-On: There are two ways to automatically turn on the amplifier. Most aftermarket car stereo head units will have a remote turn-on lead, which can be extended to the amplifier location and connected to the amp's Remote terminal. If connecting the amplifier to a factory stereo, or a head unit without a remote turn-on lead, the amp can automatically turn on using the DC Offset mode. The amp detects a 6-volt DC surge on the signal inputs and turns the amplifier on. There is no switch on the amp to select the Turn-On method.

Protection Circuitry: The DXA250.4 has protection circuitry that will turn the amp off in the event of overheating, over voltage (over 16 volt input), under voltage (under 10 volt input), and short circuit (speaker output). If the Protection LED on the right side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.

Dual Input Sensitivity: The DXA250.4 can receive low- or high-level signals from your car stereo source unit at the amplifier's left and right, RCA inputs. The low-level signal can be sent from the source unit's RCA line-level outputs. In this case, the Input Sensitivity switch on the amp should be set to "LO". A high-level signal can come from the source unit's speaker outputs, and connected to the amplifier using the Kicker KISL adapters. The Input Level switch should be set to "HI".

Fail-Safe Integration Technology (FIT): FIT utilizes isolated differential inputs, rejecting noise and electrical interference for the quietest operation possible. FIT also allows Kicker amps to accept output from nearly any factory or aftermarket head unit.

Stereo-and-Mono-Simultaneously (SAMS): The amp has the capability of powering a pair of full-range speakers and a mono subwoofer from one amplifier. The full-range can be connected normally on one pair of channels, while the subwoofer (4 ohms) can be powered by bridging the remaining pair of channels. The SAMS wiring diagram can be found in the Owner's Manual.

Controls

Input Level: The The DXA250.4 has a two position (in/out) switch to set the input level type. It can be pressed in for High (for speaker level) or set to out for Low (for line level). You should not mix low and high inputs signals to the amp.

Fader Switch: This 4-channel amplifier can accept signals from one or two sets of inputs. If you are running two sets (front and back), the amp's Fader switch should be pressed in to the ON position. If you want to drive all four channels from one set of inputs, the switch should be left in the OFF position. With the fader Off, the four channels will receive the same volume of signal, and you will not be able to adjust the fader front to back.

Audio Controls: The amplifier has two independent pairs of channels (labeled Amp 1 and Amp 2), each with separate controls. A small screwdriver is needed to set the rotary controls. Amp 1 and Amp 2 have the following controls:

  • Gain: The input gain is continuously variable, labeled 0 to 11. The gain range is governed by the input level switch: 250mV to 10V for speaker level (HI) and 125mV to 5V for line level (LO).
  • Crossover Frequency: Each crossover can be set for low-pass (LO), high-pass (HI), or full-range operation (OFF). The crossover frequency range is continuously variable between 50 Hz and 200 Hz. The crossover slope is 12 dB per octave. It is possible to set one crossover to low-pass and the other to high-pass.
  • KickEQ Bass Boost: The KickEQ bass boost circuit provides a signal boost centered at 40 Hz. The bass boost is continuously variable between 0 and 12dB.

Installation

Wiring Recommendations: Kicker recommends that the amplifier be connected to the vehicle's battery using 8 Gauge power and ground wiring. An external 60 amp fuse should be installed on the power wire within 18" of the battery. There are no fuses included or built into the amplifier.

Connections

Left Side of Amplifier:

  • GND (ground): screw terminal; accepts spade connector up to 0.5" wide
  • REM (remote turn-on): screw terminal; accepts spade connector up to 0.33" wide
  • +12V (power): screw terminal; accepts spade connector up to 0.5" wide
  • Speaker Outputs: four pairs of screw terminals; accepts spade connectors up to 0.32" wide

Right Side of Amplifier:

  • RCA Inputs: two pairs of RCA jacks, used for line level or speaker level inputs with KISL
Write Your Own Review
You're reviewing:Kicker - 44KKP412 - 12 inch Kicker Sub and 4CH Amp Package
SSL Certificate
Copyright © 2017 Ministry of Bass. All rights reserved.