Kicker - KKP212 - 12 inch Kicker Sub and 2CH Amp Package

Special Price $399.00 Regular Price $459.00
Hurry up! Only 1 left in stock

Kicker - KKP212 - 12 inch Kicker Sub and 2CH Amp Package

Product Info

Kicker KKP212 2 Channel 12" C124 Kickpack Amplifiers and Loaded Enclosures Package


VC124 Enclosure Technical Specifications


Impedance (ohms)

Power (watts/Channel) 2Ω Stereo

60 x 2
Power (watts/Channel) 4Ω Stereo

30 x 2
Power (watts/Channel) 4Ω Bridged

125 x 1
DIM A (cm)

DIM B (cm)

DIM C (cm)

DIM D (cm)

DXA125.2 Amplifier Features and Specs

RMS Power Output (Watts x Channels) 30 x 2
Peak Power Output (Watts x Channels) 250 x 1
Power at 2 Ohms (Watts x Channels) 60 x 2
Bridged Power (Watts x Channels) 125 x 1
Minimum Impedance Bridged 4
Minimum Impedance Unbridged 2
Best Frequency Response 10-20000 Hz
THD at Rated RMS Power 1%
Signal to Noise Ratio 95 dB
Input Voltage 14.4v
Amplifier Class AB
Low-Pass Crossover Frequency 50-200 Hz
Low-Pass Slope (dB/octave) 12 dB/octave
High-Pass Crossover Frequency 50-200 Hz
High-Pass Slope (dB/octave) 12 dB/octave
Bass Boost 0-12 dB
Bass Boost Frequency 40 Hz
Fan Cooled No
Fuse Rating 40
Speaker Level Inputs RCA
Preamp Outputs No
Width (inches) 8-3/16
Height (inches) 2-3/8
Depth (inches) 7-1/8
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over the full frequency range of the amp with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels at a reference of 1 watt. CEA-2006 allows consumers to compare car amplifiers and receivers on equal footing. Measured under CEA-2006 conditions the Kicker DXA125.2 is rated at 30 watts RMS x 2 channels into a 4-ohm load and the signal to noise ratio is >95 dB. Additional specs listed in the manual (but not listed as CEA-2006 compliant) include 60 watts RMS x 2 channel into a 2-ohm load (measured using a 14.4 volt power supply with no more than 1% THD+N) and 95 dB signal-to-noise ratio (measured at the rated power output).

Auto Turn-On: There are two ways to automatically turn on the amplifier. Most aftermarket car stereo head units will have a remote turn-on lead, which can be extended to the amplifier location and connected to the amp's Remote terminal. If connecting the amplifier to a factory stereo, or a head unit without a remote turn-on lead, the amp can automatically turn on using the DC Offset mode. The amp detects a 6-volt DC surge on the signal inputs and turns the amplifier on. There is no switch on the amp to select the Turn-On method.

Protection Circuitry: The DXA125.2 has protection circuitry that will turn the amp off in the event of overheating, over voltage (over 16 volt input), under voltage (under 10 volt input), and short circuit (speaker output). If the Protection LED on the right side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.

Dual Input Sensitivity: The DXA125.2 can receive low- or high-level signals from your car stereo source unit at the amplifier's left and right RCA inputs. The low-level signal can be sent from the source unit's RCA line-level outputs. In this case, the Input Sensitivity switch on the amp should be set to "LO". A high-level signal can come from the source unit's speaker outputs, and connected to the amplifier using the Kicker KISL adapters. The Input Level switch should be set to "HI".

Fail-Safe Integration Technology (FIT): FIT utilizes isolated differential inputs, rejecting noise and electrical interference for the quietest operation possible. FIT also allows Kicker amps to accept output from nearly any factory or aftermarket head unit.

Stereo-and-Mono-Simultaneously (SAMS): The amp has the capability of powering a pair of full-range speakers and a mono subwoofer from one pair of channels. Using passive crossovers, you can high-pass the signals to the full-range speakers and to low-pass the signals to the subwoofers. The SAMS wiring diagram can be found in the Owner's Manual.


Input Level: The DXA125.2 has a two position (in/out) switch to set the input level type. It can be pressed in for High (for speaker level) or set to out for Low (for line level).

Gain: The input gain is continuously variable, labeled 0 to 11. The gain range is governed by the input level switch: 250mV to 10V for speaker level (HI) and 125mV to 5V for line level (LO). A small screwdriver is needed to adjust the gain.

Crossover Frequency: The crossover can be set for low-pass (LO), high-pass (HI), or full-range operation (OFF). The crossover frequency range is continuously variable between 50 Hz and 200 Hz. The crossover slope is 12 dB per octave A small screwdriver is needed to set the crossover cutoff frequency.

KickEQ Bass Boost: The KickEQ bass boost circuit provides a signal boost centered at 40 Hz. The bass boost is continuously variable between 0 and 12dB. A small screwdriver is needed to adjust the amount of bass boost.

Write Your Own Review
You're reviewing:Kicker - KKP212 - 12 inch Kicker Sub and 2CH Amp Package
SSL Certificate
Copyright © 2017 Ministry of Bass. All rights reserved.