Cyclops - Paralyser P205 - Immobiliser

A$200.00
Shipped in 2-3 Working Days
SKU
P205

Paralyser P205

Paralyser P205 Car Immobiliser

Installation available for an extra $150
(Installation available in Adelaide only)
Please contact us on 08 8371 5121 to book a time.

Introduction

This Australian Standards approved immobiliser provides two circuits of automatic engine immobilisation operated by an electronically coded transponder with a dash mounted high intensity red LED. The system is fully automated and thus the user doesn't have to arm or disarm
Operation•
Hands-free operation
Simply turn the ignition switch of the car to ON, the transponder tag on the key ring will automatically disarm the system

Auto Arming
The car's engine is automatically immobilised 40 seconds after the engine has stopped. The auto-arming feature is disabled while the system is disarmed and the ignition switch is in the ON position
Available for light trucks
The P205 system is also available for light trucks which use a +24 Volts battery supply. 

Immobilisation
Dual Immobilisation Circuits
The system features two independent 30 Amp rated, normally open immobilisation circuits, which break engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits
Safety circuitry in case of power failure
System sources alternate power from ignition if main power is lost
Third circuit of immobilisation (optional)
Additional immobilisation circuits can be added to conform with insurance company requirements
Component protection against harsh road conditions
All relays are fully encapsulated to provide protection against dust and moisture

Controllers
Two Transponder tags
Encoded digital signature device with 281,000,000,000,000+ code combinations
•Batteries not required
Transponder tags use induced power signals from car, requires no battery replacement or servicing

•Accessibility
Recommended disarm method for users with limited hand movement
•Remote control with transponder enhancements
Allows the immobiliser to disarm automatically when ignition switch is turned on
•Large system memory
Allows system to track four controllers each operating with a independent code. This allows four users to disarm the system, and erasure of individual tags
•Controller re-programming
Service technician can delete lost or stolen controllers from memory

Wiring
Security wiring
All cables extending from the control module are black and same diameter. Identifying wire tags are removed by the installer during installation of the system
•Plug and play for service
Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves
•Security housing
Connector plug is enclosed within module case to prevent access by thief
•Stealth wiring
Cutting any immobilisation wiring will still leave the car secure. Bypassing security is not possible by simply removing the system from the vehicle

Override
Emergency Personal Identification Number (PIN) override
If the valid controller are lost, stolen or broken, the user by over-ride the system by enter the secret four digits via the ignition switch
•Alterable PIN
A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number
•One shot override
Immobiliser always re-arms to protect vehicle. Re-enter PIN if vehicle needs to be driven after auto-arming has occurred
•PIN card
A record of the factory programmed override PIN is supplied on handy wallet sized card
Visual Output•Super bright red dash LED
This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window

Specifications•
Current draw
•Wide Operating voltage
Operating voltage +9VDC to +15VDC
•Operating temperature
-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin
•Polarity protection
The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery
•Short circuit protection
The power supply wire to the system is protected against an internal fault within the system

Warranty
Manufacturers warranty on Control module
Guarantees control module is free from manufacturing defects for 24 months from time of purchase
•Manufacturers warranty on Transponder tags
Guarantees Transponder tags are free from manufacturing defects for 12 months from time of purchase
Standards Compliance
Australian Standard for vehicle Immobilisers
AS/NZS 4601:1999 - Australian Standards website.
•Manufactured in ISO9001 facility. Built within world standard production facility
•AS/NZS 4601 sundry standards of compliance (or parts thereof)
AS1939 - Degrees of protection provided by enclosures for electrical equipment (IP Codes)
AS3300 - Approval and test specification - General requirements for household and similar electrical appliances
AS/NZS3548 Limits and methods of measurement of radio disturbance characteristics of information technology equipment
AS/NZS3749 - Intruder alarm systems - Road vehicles
AS/NZS4268 - Radio equipment and systems - Short range devices
AS/NZS61000 - Electromagnetic compatibility (EMC)
NZS6300 - Approval and test specification - General requirements for household and similar electrical appliances
ISO7637 - Road vehicles - Electrical disturbance by conduction and coupling
IEC61000 - Electromagnetic compatibility (EMC)
ASTM B117 - Standard practice for operating salt spray (fog) apparatus

Write Your Own Review
You're reviewing:Cyclops - Paralyser P205 - Immobiliser
SSL Certificate
Copyright © 2016 Ministry of Bass. All rights reserved.